Easy Power! Your 2016-2018 Audi A6/A7 3.0T with the updated CREC supercharged engine capable of massive power gains in only minutes from an IE ECU Tune. Unleash hidden horsepower and torque to turn your sporty A6 or A7 into an extremely competitive powerhouse!

Maximised Output

IE ECU calibrations are dedicated to perfecting every section of the mapping to deliver a fully realized performance file right out of the gate. Maximized for full performance potential on the drag strip and road course while maintaining full comfort and reliability on your daily commute. Get ready to experience IE's Performance Software For your Audi CREC 3.0T Supercharged engine in only minutes from the comfort of your home garage or driveway. 

Stage 1, Stock Hardware: Gain up to 166hp on stock hardware

Stage 2, Single Pulley: Up to 524hp with a supercharger pulley upgrade

• Horsepower & torque gains maximized
• Optimized for all climates & conditions
• 91, 93, & E85 octanes available (95, 98, RON & E85)
• ECU safely adapts between E65-E85 Ethanol
• Rev limiter increased to 7200 RPM (requires TCU tune)
• Cluster reprogrammed to show new 7200 RPM limit
• Auto start/stop disabled
• Activates brake boosting
• Road speed limiters removed
• Direct port OBDII at-home flashing
• Easy octane switching takes only minutes
• Upgrade stages to match hardware upgrades
• Simple on/off feature toggling
• Read and clear diagnostic/problem codes
• Easy to use Data-logger

Add Transmission Tune

All stages of IE ECU calibrations for the C7.5 A6 & A7 are compatible with the matching IE ZF8 AL551 Transmission TCU Tune and is highly recommended to reach the advertised power figures. Without a matching TCU tune, the transmission will short shift the powerband at 6300 RPM vs. the ECU tune's peak power at 7200RPM -leaving power on the table. Adding the TCU upgrade also modifies shift speed, torque limit maps, line pressure, and launch control functions resulting in a complete ECU & TCU performance package.

E85 Ethanol

E85 fuel unlocks the most performance potential from our ECU tunes for your Audi S6 or S7. Ethanol contains tons of oxygen, burns cooler, and has a high resistance to knock. This provides more horsepower and torque than running conventional gasoline and is more readily available (in most states) and less expensive than race gas. E85 is an optional fuel map included with all tune purchases.

Brake Boost

Commonly used in roll racing, Brake Boosting allows you to build extra boost by applying brake pressure while accelerating. Release the brake pressure for a "rolling launch" or extra surge of power. Brake Boost is included on all tune stages.

Increased RPM

Take full advantage of your supercharger with a larger power band. RPM limits have been raised to 7200RPM in all stages. This higher RPM limit not only extends the power band, but also unlocks 20+HP in the upper RPM range! Transmission TCU Tune is required to unlock higher RPM.

Optimised Cooling

To combat power-robbing heat soak generated from the supercharged engine the factory coolant pump calibration has been modified in all ECU Tune stages. This new configuration runs the coolant pump at 50% duty when the ignition is keyed on pushing coolant through the charge coolers and reducing heat faster without the engine running. This helps avoid heat soak and provides faster recovery in-between runs or while staging at the track. During driving or when the intake temp is above 20C, the coolant pump operates at 100% for maximum cooling efficiency.

Reliability Testing

IE's fully proven software brings track-ready ECU programming to your supercharged V6 engine while retaining factory comfort and reliability. IE's own tuning technology suite is used to completely reverse-engineer the factory ECU mapping, allowing our software engineers access to realign all safety protocols and sensors for the new performance calibration. Every tune parameter undergoes months of testing on our in-house dyno systems that utilize the world's only Sea Level Generator developed specifically to verify tune operations in any condition. Confidently drive from LA to Pikes Peak with power that will keep you smiling every mile!

Stage 1

Require Hardware

Stage 2 Single Pulley

• AUDI A6 2016-2018 C7.5 3.0T Supercharged (CREC engine code)
  
• AUDI A7 2016-2018 C7.5 3.0T Supercharged (CREC engine code)

Power Results

IE's POWERlink Cable and Flash Wizard software gives you the freedom to quickly flash your new IE ECU Tune. Simply plug your POWERlink into the vehicle's OBD-2 port and follow the on-screen directions, it's that easy!

IESOVJ21 (Stage 1)

IESOVJ22 (Stage 2)

Manufactured by

Integrated Engineering (IE)

Five-star Support

IE's number one goal from purchase to installation is to provide you with the best customer experience in the industry. We want what you want; a simple purchase process, products that exceed expectations, and a brand that's got your back. If at any point you have any questions, need help, or require support with your new tune our educated customer support team and tuning specialists are standing by and happy to help. Purchasing an IE tune not only guarantees a quality product, but that you will always have us in your corner.

Live Fast, Buy Fun

Consumer Notice

By purchasing a motorsport/racing product ("product"), you represent that you understand and agree that: the product is not designed to meet any applicable emissions standards, whether in the USA or otherwise, the product is not C.A.R.B. compliant, and that the product is not for sale or use in California, USA nor any other jurisdiction where the sale or use is prohibited by law. Integrated Engineering, LLC makes no representations, warranties, or claims that this product complies with any applicable emissions laws and expressly disclaims any and all such representations, warranties, and claims, whether express or implied. By purchasing this product, you represent, warrant, and agree that it is your responsibility to inform yourself of any laws or regulations that may apply to your purchase and/or use of the product.